XDM260
INSTALLATION/OWNER'SꢀMANUAL
AM/FM/CDꢀReceiverꢀwithꢀDetachableꢀFace
XDM260 INSTALLATION
Wiring Diagram
Antenna Connector
Rear Preamp Output
Connect to amplifier RCA input
L-CH R-CH
RCA Cable
(sold separately)
BLUE Remote Turn-On
Connect to amplifier or power
AMP
antenna. Insulate wire if not used.
BLACK Ground
Connect to vehicle
chassis ground.
RED Accessory
Connect to ignition
circuit or switched 12 volt source.
5 AMP
AGC Fuse
YELLOW Memory
Connect to battery
circuit or constant 12 volt source.
FUSE
Right Front
Gray/Black (-)
Gray (+)
Right Rear
Violet/Black (-)
Violet (+)
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse could
damage the radio.
The XDM260 uses one
5amp AGC fuse located
in-line.
Left Front
White/Black (-)
White (+)
Left Rear
Green/Black (-)
Green (+)
3
XDM260 OPERATION
ControlꢀLocationsꢀ-ꢀReceiver
1
2
3
4
5
6
19
18
17
16
15 14
13
12
11 10
9
8
7
1
2
3
4
5
6
7
8
9
Release
11 Preset 3 / Intro
Band / Go Back
Volume Knob
Power
12 Preset 2 / Random
13 Preset 1 / Repeat
14 Display
Eject
15 Tune / Track Up
16 Tune / Track Down
17 Mode
USB Port
Auxiliary Input
Preset 6 / Folder Up
18 Audio / Menu
19 Mute
Preset 5 / Folder Down
10 Preset 4 / Play / Pause
4
XDM260 INSTALLATION
General Operation
Press RELEASE and pull away from the left side to remove.
To re-install, insert right side of faceplate first then push
left side to secure.
Faceplate Removal
Press or any other button (except EJECT) to turn the unit
Power On/Off
Mode
on. Press to turn the unit off.
Press MODE to select between AM/FM, CD player, auxiliary,
USB. Modes of operation are shown in the display.
NOTE: CD and USB modes will not appear unless a CD is
inserted or USB device is connected.
The XDM260 offers a 3.5 mm auxiliary input port on the front
panel of the unit for connecting an audio device, MP3 player,
etc. Press MODE to select auxiliary input mode.
Auxiliary Input
Adjust volume using volume knob (00-46).
Volume
Display
Press DISP to show the clock. During playback of MP3/WMA
files, ID3 tag information, elapsed time, track number and
file/folder names will automatically rotate on the display.
Press RESET upon initial installation or if abnormal
operation occurs. Reset button is located behind the front
panel.
Reset
Set the Clock
With the unit on, press and hold DISP until the clock begins
to flash, then release. Turn the volume knob to the right to
adjust the hours or to the left to adjust the minutes.
The clock will display 12-hour AM/PM time in USA frequency
12/24-hour Clock
Setup Menu
:
spacing mode (PM 10 00). In European frequency spacing
mode, the clock will display 24-hour time (22:00).
Press and hold AUDIO/MENU for more than 3 seconds to
access the setup menu. Press AUDIO/MENU momentarily
to select between the menu functions and rotate the volume
knob left/right to adjust or activate the desired function.
5
XDM260 OPERATION
General Operation - Setup Menu
Menu Function
Options
Action
Auto Station
Store
Press SELECT to seek and save 6 strong stations in the
AUTO STORE
LOCAL OFF
LOCAL ON
current band. (Tuner mode only)
Activates distance tuning (Tuner mode only).
Local/Distance
Tuning
Activates local tuning for strong station reception only (Tuner
mode only).
Programs the unit to USA tuner spacing.
FREQ USA
Tuner
Frequency
Spacing
(200kHz for FM and 10kHz for AM). (Tuner mode only)
Programs the unit to European tuner spacing.
(50kHz for FM and 9kHz for AM). (Tuner mode only)
FREQ EURO
AUX ON
AUX OFF
BEEP OFF
BEEP ON
Enables the front panel 3.5mm auxiliary input.
Disables the front panel 3.5mm auxiliary input.
Disables the confirmation beep.
Auxiliary
Input
Beep
Confirmation
Enables the confirmation beep.
Programmable
Turn On Volume
Programs unit to always turn on at a specific volume
(default is OFF). Any volume level 1-46 can be selected.
PRO-VOL #
MSG OFF
MSG ON
Disables power on message. (example: GOOD MORNING)
Enables power on message to be displayed.
Power on
Message
Programs unit to scroll information once every 15 seconds
(default).
SCROLL 15 S
Programs unit to scroll once, then show the first 10
characters on display.
Scrolling
Option
SCROLL ONCE
SCROLL ON
SCROLL OFF
DEMO OFF
DEMO ON
Programs unit to scroll continuously.
Programs unit to show the first 10 characters on the display.
Disables the demonstration mode.
Demonstration
Mode
Enables the demonstration message.
6
XDM260 INSTALLATION
General Operation
Audio Press AUDIO/MENU momentarily to select between Bass,
Treble, Balance and Fader.
BASS
TREBLE
BALANCEE
LOUDNESS
FADER
EQ
SOURCE LEVEL
Bass Press AUDIO/MENU until BASS appears then rotate volume
knob left/right to adjust ( -6 minimum / +6 maximum).
Treble Press AUDIO/MENU until TREBLE appears then rotate
volume knob left/right to adjust ( -6 minimum / +6
maximum).
Balance Press AUDIO/MENU until BAL appears then rotate volume
knob left/right to adjust (BAL 12L - BAL 12R).
BAL EVEN represents equal balance.
Fader Press AUDIO/MENU until FADER appears then rotate
volume knob left/right to adjust (FAD 12F - FAD 12R).
FAD EVEN represents equal fader.
7
XDM260 OPERATION
AM/FM Tuner Operation
Seek Tuning Press TUNE
or TUNE
momentarily to seek to the
nn
ll
next strong station.
Manual Tuning Press and hold TUNE
or TUNE
until "MANUAL"
nn
ll
appears, then press TUNE
to change radio frequency up or down one step at a time.
Press and hold to advance quickly.
or TUNE
momentarily
nn
ll
Band Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands.
Storing and Recalling Up to 18 FM stations and 12 AM stations can be stored. To
Station Presets store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
2 seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
8
XDM260 INSTALLATION
CD Player Operation
Insert CD With the label facing up, insert a standard size CD into the
CD slot. The CD will automatically begin playback.
Eject CD Press EJECT to eject the CD. The unit will change to
previous mode of operation. If the disc is not removed
within 10 seconds, the unit will reload the disc. The unit
does not have to be turned on to eject CD.
Track Select
Press TRACK
to skip to the beginning of the next
ll
track. Press TRACK
to return to the beginning of the
nn
current track. Pressing TRACK
beginning of the previous track.
again skips to the
nn
Fast Forward/Reverse
Press and hold TRACK
or TRACK
on the remote
ll
nn
control to fast forward or reverse a track.
Pause
Intro
Press
Press
/
/
II to temporarily stop CD playback.
l
l
II again to resume playback.
Press INT to enter the Intro menu, then turn the volume
knob to select one of the following options:
• OFF - Cancels the INT function.
• ALL - Plays the first 10 seconds of each track.
Repeat
Press RPT to enter the Repeat menu, then turn the volume
knob to select one of the following options:
• ALL - Plays all tracks on CD.
• SONG - Continuously repeats selected song.
Random
Press RDM to enter the Random menu, then turn the
volume knob to select one of the following options:
• OFF - Cancels the RDM function.
• ALL- Plays all tracks in random order.
CD-R/CD-RW
Compatibility
Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method. In
addition, the following CDs may be incompatible with this
unit:
CDs exposed to extreme temperatures or direct sunlight
for extended periods of time, CDs recorded in which a
recording session failed or a re-recording was attempted
and, or encrypted or copy-protected CDs which do not
conform to the audio CD-DA red book recording standard.
9
XDM260 OPERATION
CD Player Operation - MP3/WMA Files
Playing an MP3/WMA CD When an MP3/WMA encoded disc is first inserted,
“LEAD" will appear in the display. Depending on the number
of files and folders, this may take several seconds.
Displaying Information ID3 tag and file/folder information will be automatically
changed during playback. Press DISP to view the clock.
Default display will resume after five seconds.
Character Support Maximum character display information
• Track name – 64 character maximum
• Directory name – 64 character maximum
• *Song title – 64 character maximum
• *Artist name – 64 character maximum
• *Album name – 64 character maximum
*Song title, artist name and album name will only be
displayed if included with the MP3/WMA file.
When referring to MP3/WMA playback, the following terms
are synonymous:
• File name and track name
• Folder name and directory name
Repeat Press RPT to choose between:
• All - Plays all tracks on CD.
• Song - Continuously repeats selected track.
• Folder - Continuously repeats all files in folder.
Random Press RDM to choose between:
• Off - Cancels RDM function.
• Songs - Plays all tracks in random order.
• Folder - Plays all tracks in folder in random order.
Intro Press INT to enter the Intro menu, then turn the volume
knob to select one of the following options:
• Off - Cancels the INT function.
• Songs - Plays first 10 seconds of each track.
• Folder - Plays first 10 seconds of each track in folder.
10
XDM260 INSTALLATION
CD Player Operation - MP3/WMA Files
Media Compatibility
The following types of discs/files are compatible:
• CD-ROM (ISO), CD-R, CD-RW
• CD-DA
• MP3 data
• WMA data
The following types of discs/files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management).
• WMA lossless format
• Discs recorded with Track At Once or packet writing
• MP3 PRO format
• MP3 playlists
• WAV format
Playback Order
MP3/WMA playback sequence is based on recorded order
of files and begins in the root folder of the disc. Any empty
folders or folders that do not include MP3/WMA files are
skipped. This unit may not play files in the order they were
recorded in. Refer to your recording software’s user’s
manual for more information.
Compatible Recording
Formats
• ISO9660 level 1
• ISO9660 level 2
• Yellow Book MODE 1
• Yellow Book MODE 2 FORM 1
• Multi session
• Maximum folders and files - 256
• Maximum folder levels - 8
• MPEG-1/2/2.5 Audio Layer-3
ISO9660 standards:
• Maximum nested folder depth is 8 (including the root
folder).
• Valid characters for folder/file names are letters A-Z (all
caps), numbers 0-9, and “_” (underscore). Somec haracters
may not be displayed correctly, depending on the character
type.
• This device can play back discs in Joliet, Romeo, and other
standards that conform to ISO9660. MP3/WMA written in the
formats other than the above may not play and/or their file
names or folder names may not be displayed properly.
11
XDM260 OPERATION
CD Player Operation - MP3/WMA Files
Additional MP3/WMA
When playing a disc recorded with regular audio files
(CD-DA or .WAV) and MP3/WMA files, the unit will play the
MP3/WMA files only.
Information
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be
played.
Do not attempt to play discs which contain non-MP3/WMA
files with the MP3/WMA extension.
Sampling Frequency
Rates
MP3
8kHz ~ 48kHz
8kHz ~ 48kHz
WMA
Transfer Bit rates
MP3
8kbps ~ 320kbps constant
Variable bit rates
WMA
8kbps ~ 384kbps constant
Variable bit rates
Note: Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3 Tag Display
ID3 tags Version 1.0 to 2.0.
This model will not display ID3 Version 2.0 or greater tags.
Recommended Settings
For best results, use the following settings when burning an
MP3 disc:
128kbps or higher constant bit rate
44.1kHz or higher sampling frequency
For best results, use the following settings when burning a
WMA disc:
64kbps or higher constant bit rate
32kHz or higher sampling frequency
12
XDM260 INSTALLATION
USB Operation
Connecting a USB Device
To play MP3/WMA files from most USB mass storage
devices, line up the USB connector and insert the USB
device into the XDM260's USB port.
(sold separately)
Playing Music
When a USB device is first connected, “LEAD” will appear in
the display and playback will begin momentarily. Depending
on the number of files and folders, it may take several
seconds for the device to begin playing. If no valid MP3/
WMA files are detected, “NO FILE” will be displayed and the
last mode will be resumed.
Track Select
Press TRACK
to skip to the beginning of the next
ll
track. Press TRACK
to return to the beginning of the
nn
current track. Pressing TRACK
beginning of the previous track.
again skips to the
nn
Fast Forward and
Reverse
Press and hold TRACK
or TRACK
on the remote
ll
nn
control to fast forward or reverse a track.
Pause
Press
Press
/
/
II to temporarily stop USB playback.
l
l
II again to resume playback.
Displaying Information
ID3 tag and file/folder information will be automatically
changed during playback. Press DISP to view the clock.
Default display will resume after five seconds.
Repeat
Random
Intro
Press RPT to choose between:
• All - Plays all tracks on USB device.
• Song - Continuously repeats selected track.
• Folder - Continuously repeats all files in folder.
Press RDM to choose between:
• Off - Cancels RDM function.
• All - Plays all tracks in random order.
• Folder - Plays all tracks in folder in random order.
Press INT to enter the Intro menu, then turn the volume
knob to select one of the following options:
• Off - Cancels the INT function.
• All - Plays first 10 seconds of each track.
• Folder - Plays first 10 seconds of each track in folder.
13
XDM260 OPERATION
USB Operation
Character Support
Maximum character display information
• Track name – 64 character maximum
• Directory name – 64 character maximum
• *Song title – 64 character maximum
• *Artist name – 64 character maximum
• *Album name – 64 character maximum
*Song title, artist name and album name will only be
displayed if included with the MP3/WMA file.
Media Compatibility
The following types of files are compatible:
• MP3 data
• WMA data
The following types of files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management).
• WMA lossless format
• MP3 PRO format
• MP3 playlists
• WAV format
Playback Order
MP3/WMA playback sequence is based on order the files
are copied to the USB/SD device and begins in the root
folder. Any empty folders or folders that do not include MP3/
WMA files are skipped. Depending on your software, the
playback order may vary.
Playback Capacity
• Maximum number of files: 2000
• Maximum number of folders: 500 plus the root directory
• Maximum number of files in each folder and root: 2000
• Maximum number of folder levels (sub folders): 8
(7 levels plus the root)
Note: If the number of files/folders exceeds the maximum
outlined above, the additional files/folders will be ignored.
Note: Devices that exceed the maximum number of files or
folders may not function properly.
USB Device Compatibility Due to the differences of USB devices, some devices may
not be compatible. USB devices must be ‘mass storage
class’ and formatted to the FAT or FAT32 file system in
order to ensure compatibility. USB devices must be 32GB or
smaller in capacity to be compatible.
14
XDM260 INSTALLATION
USB Operation
Additional MP3/WMA
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be
played. Do not attempt to play non-MP3/WMA files with the
MP3/WMA extension.
Information
Sampling Frequency
Rates
MP3
8kHz ~ 48kHz
8kHz ~ 48kHz
WMA
Transfer Bit rates
MP3
8kbps ~ 320kbps constant
Variable bit rates
WMA
8kbps ~ 384kbps constant
Variable bit rates
Note: Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3 Tag Display
ID3 tags Version 1.0 to 2.0
Note: If an invalid ID3 tag version is detected, "NO
SUPPORT" will scroll on the display.
15
XDM260 OPERATION
Troubleshooting
Problem
Cause
Action
Yellow wire not connected or incorrect
voltage Red wire not connected or
incorrect voltage
Check connections for proper
voltage (11~16VDC)
Unit will not turn on
(no power)
Black wire not connected
Fuse blown
Check connection to ground
Replace fuse
Speaker wires not connected
Check connections at speakers
Unit has power
(but no sound)
Insulate all bare speaker wires
from each other and chassis
ground
One or more speaker wires touching
each other or touching chassis ground
Yellow or red wire touching chassis
ground
Check for pinched wire
Unit blows fuses
Speaker wires touching chassis ground
Incorrect fuse rating
Check for pinched wire
Use fuse with correct rating
Unit is not mounted correctly or
backstrap is not secure
Check mounting sleeve and
backstrap support
Excessive skipping
Physical defect in media (CD, CD-R or
CD-RW)
Check media for scratches
Press eject or RESET
Press eject or RESET
Disc read error
ERR FILE appears
on display
Focus error or disc is in upside down
The WMA file is copy-protected by DRM Write disc using WMA files that
(Digital Rights Management)
are not copy-protected
NO FILE appears
on display
No playable MP3/WMA files found on
the device
Check the device for valid
MP3/WMA files
CD mechanism position out of
alignment
Press EJECT to reset CD
mechanism position
Unit will not accept
a disc
Remove 2 transit screws
located on top of the unit
CD transit screws still in place
NO SUPPORT appears
on display
Version 1.0 to 2.0 ID3 tags are
supported.
An invalid ID3 tag version is present
16
XDM260 INSTALLATION
Limited One Year Warranty
This warranty gives you specific legal
rights. You may also have other rights
which vary from state to state.
What to do?
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any
custom controls may save you a service
call.
Dual Electronics Corp. warrants this
product to the original purchaser to be free
from defects in material and workmanship
for a period of one year from the date of
the original purchase.
2. If you require service during the
warranty period, you must carefully
pack the product (preferably in the
original package) and ship it by prepaid
transportation with a copy of the original
receipt from the retailer to an
Dual Electronics Corp. agrees, at our
option, during the warranty period,
to repair any defect in material or
workmanship or to furnish an equal
new, renewed or comparable product
(whichever is deemed necessary) in
exchange without charges, subject to
verification of the defect or malfunction and
proof of the date of purchase. Subsequent
replacement products are warranted for
the balance of the original warranty period.
authorized service center.
3. Please describe your problem in
writing and include your name, a
return UPS shipping address (P.O. Box
not acceptable), and a daytime phone
number with your shipment.
4. For more information and for the
location of the nearest authorized
service center please contact us by one
of the following methods:
Who is covered? This warranty is extended
to the original retail purchaser for products
purchased from an authorized Dual dealer
and used in the U.S.A.
• Call us toll-free at 1-866-382-5476
• E-mail us at [email protected]
What is covered? This warranty covers all
defects in material and workmanship in
this product. The following are not covered: Exclusion of Certain Damages: This
software, installation/removal costs,
damage resulting from accident, misuse,
abuse, neglect, product modification,
improper installation, incorrect line
voltage, unauthorized repair or failure
to follow instructions supplied with the
product, or damage occurring during
return shipment of the product. Specific
warranty is exclusive and in lieu of any
and all other warranties, expressed or
implied, including without limitation the
implied warranties of merchantability and
fitness for a particular purpose and any
obligation, liability, right, claim or remedy
in contract or tort, whether or not arising
from the company’s negligence, actual
license conditions and copyright notices for or imputed. No person or representative
com.
is authorized to assume for the company
any other liability in connection with the
sale of this product. In no event shall the
company be liable for indirect, incidental or
consequential damages.
17
XDM260 OPERATION
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
18
XDM260 INSTALLATION
Specifications
CD Player Frequency response: 20Hz-20kHz
Channel separation @ 1kHz: >60dB
D/A converter: 1 Bit
FM Tuner Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: >30dB
Frequency response: 30Hz-13kHz
AM Tuner Tuning range: 530kHz-1710kHz
Usable sensitivity: <42dBu
Frequency response: 30Hz-2.2kHz
General Speaker output impedance: 4~8 ohms
Line output voltage: 2 Volts RMS
Dimensions: 7" x 7" x 2" (178 x 178 x 50 mm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 18 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 70dBA (reference: 1 watt into 4 ohms)
19
Dual Electronics Corp.
Toll Free: 1-866-382-5476
9AM-5PM EST, Monday-Friday
©2013 Dual Electronics Corp. All rights reserved.
Other trademarks and trade names are those of their respective owners.
NSA0813-V03
|